{"tests":[{"name":"kubeadm.v1.35.1.flannel.base/node_readiness","result":"PASS","duration":21849475683,"output":""},{"name":"kubeadm.v1.35.1.flannel.base/nginx_deployment","result":"PASS","duration":38776583877,"output":""},{"name":"kubeadm.v1.35.1.flannel.base/NFS_deployment","result":"PASS","duration":47112552432,"output":"        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n"},{"name":"kubeadm.v1.35.1.flannel.base","result":"PASS","duration":239648744110,"output":"        cluster.go:125: [config/images] Pulled registry.k8s.io/kube-apiserver:v1.35.4\n        cluster.go:125: [config/images] Pulled registry.k8s.io/kube-controller-manager:v1.35.4\n        cluster.go:125: [config/images] Pulled registry.k8s.io/kube-scheduler:v1.35.4\n        cluster.go:125: [config/images] Pulled registry.k8s.io/kube-proxy:v1.35.4\n        cluster.go:125: [config/images] Pulled registry.k8s.io/coredns/coredns:v1.13.1\n        cluster.go:125: [config/images] Pulled registry.k8s.io/pause:3.10.1\n        cluster.go:125: [config/images] Pulled registry.k8s.io/etcd:3.6.6-0\n        cluster.go:125: [init] Using Kubernetes version: v1.35.4\n        cluster.go:125: [preflight] Running pre-flight checks\n        cluster.go:125: \t[WARNING Service-kubelet]: kubelet service is not enabled, please run 'systemctl enable kubelet.service'\n        cluster.go:125: [preflight] Pulling images required for setting up a Kubernetes cluster\n        cluster.go:125: [preflight] This might take a minute or two, depending on the speed of your internet connection\n        cluster.go:125: [preflight] You can also perform this action beforehand using 'kubeadm config images pull'\n        cluster.go:125: [certs] Using certificateDir folder \"/etc/kubernetes/pki\"\n        cluster.go:125: [certs] Generating \"ca\" certificate and key\n        cluster.go:125: [certs] Generating \"apiserver\" certificate and key\n        cluster.go:125: [certs] apiserver serving cert is signed for DNS names [kubernetes kubernetes.default kubernetes.default.svc kubernetes.default.svc.cluster.local localhost] and IPs [10.96.0.1 10.0.0.5]\n        cluster.go:125: [certs] Generating \"apiserver-kubelet-client\" certificate and key\n        cluster.go:125: [certs] Generating \"front-proxy-ca\" certificate and key\n        cluster.go:125: [certs] Generating \"front-proxy-client\" certificate and key\n        cluster.go:125: [certs] External etcd mode: Skipping etcd/ca certificate authority generation\n        cluster.go:125: [certs] External etcd mode: Skipping etcd/server certificate generation\n        cluster.go:125: [certs] External etcd mode: Skipping etcd/peer certificate generation\n        cluster.go:125: [certs] External etcd mode: Skipping etcd/healthcheck-client certificate generation\n        cluster.go:125: [certs] External etcd mode: Skipping apiserver-etcd-client certificate generation\n        cluster.go:125: [certs] Generating \"sa\" key and public key\n        cluster.go:125: [kubeconfig] Using kubeconfig folder \"/etc/kubernetes\"\n        cluster.go:125: [kubeconfig] Writing \"admin.conf\" kubeconfig file\n        cluster.go:125: [kubeconfig] Writing \"super-admin.conf\" kubeconfig file\n        cluster.go:125: [kubeconfig] Writing \"kubelet.conf\" kubeconfig file\n        cluster.go:125: [kubeconfig] Writing \"controller-manager.conf\" kubeconfig file\n        cluster.go:125: [kubeconfig] Writing \"scheduler.conf\" kubeconfig file\n        cluster.go:125: [control-plane] Using manifest folder \"/etc/kubernetes/manifests\"\n        cluster.go:125: [control-plane] Creating static Pod manifest for \"kube-apiserver\"\n        cluster.go:125: [control-plane] Creating static Pod manifest for \"kube-controller-manager\"\n        cluster.go:125: [control-plane] Creating static Pod manifest for \"kube-scheduler\"\n        cluster.go:125: [kubelet-start] Writing kubelet environment file with flags to file \"/var/lib/kubelet/kubeadm-flags.env\"\n        cluster.go:125: [kubelet-start] Writing kubelet configuration to file \"/var/lib/kubelet/instance-config.yaml\"\n        cluster.go:125: [patches] Applied patch of type \"application/strategic-merge-patch+json\" to target \"kubeletconfiguration\"\n        cluster.go:125: [kubelet-start] Writing kubelet configuration to file \"/var/lib/kubelet/config.yaml\"\n        cluster.go:125: [kubelet-start] Starting the kubelet\n        cluster.go:125: [wait-control-plane] Waiting for the kubelet to boot up the control plane as static Pods from directory \"/etc/kubernetes/manifests\"\n        cluster.go:125: [kubelet-check] Waiting for a healthy kubelet at http://127.0.0.1:10248/healthz. This can take up to 4m0s\n        cluster.go:125: [kubelet-check] The kubelet is healthy after 502.142171ms\n        cluster.go:125: [control-plane-check] Waiting for healthy control plane components. This can take up to 30m0s\n        cluster.go:125: [control-plane-check] Checking kube-apiserver at https://10.0.0.5:6443/livez\n        cluster.go:125: [control-plane-check] Checking kube-controller-manager at https://127.0.0.1:10257/healthz\n        cluster.go:125: [control-plane-check] Checking kube-scheduler at https://127.0.0.1:10259/livez\n        cluster.go:125: [control-plane-check] kube-controller-manager is healthy after 1.004639572s\n        cluster.go:125: [control-plane-check] kube-scheduler is healthy after 1.567849471s\n        cluster.go:125: [control-plane-check] kube-apiserver is healthy after 4.002086533s\n        cluster.go:125: [upload-config] Storing the configuration used in ConfigMap \"kubeadm-config\" in the \"kube-system\" Namespace\n        cluster.go:125: [kubelet] Creating a ConfigMap \"kubelet-config\" in namespace kube-system with the configuration for the kubelets in the cluster\n        cluster.go:125: [upload-certs] Skipping phase. Please see --upload-certs\n        cluster.go:125: [mark-control-plane] Marking the node localhost as control-plane by adding the labels: [node-role.kubernetes.io/control-plane node.kubernetes.io/exclude-from-external-load-balancers]\n        cluster.go:125: [mark-control-plane] Marking the node localhost as control-plane by adding the taints [node-role.kubernetes.io/control-plane:NoSchedule]\n        cluster.go:125: [bootstrap-token] Using token: 66zqob.vyiw1jnzvsvlqxl2\n        cluster.go:125: [bootstrap-token] Configuring bootstrap tokens, cluster-info ConfigMap, RBAC Roles\n        cluster.go:125: [bootstrap-token] Configured RBAC rules to allow Node Bootstrap tokens to get nodes\n        cluster.go:125: [bootstrap-token] Configured RBAC rules to allow Node Bootstrap tokens to post CSRs in order for nodes to get long term certificate credentials\n        cluster.go:125: [bootstrap-token] Configured RBAC rules to allow the csrapprover controller automatically approve CSRs from a Node Bootstrap Token\n        cluster.go:125: [bootstrap-token] Configured RBAC rules to allow certificate rotation for all node client certificates in the cluster\n        cluster.go:125: [bootstrap-token] Creating the \"cluster-info\" ConfigMap in the \"kube-public\" namespace\n        cluster.go:125: [kubelet-finalize] Updating \"/etc/kubernetes/kubelet.conf\" to point to a rotatable kubelet client certificate and key\n        cluster.go:125: [addons] Applied essential addon: CoreDNS\n        cluster.go:125: [addons] Applied essential addon: kube-proxy\n        cluster.go:125: \n        cluster.go:125: Your Kubernetes control-plane has initialized successfully!\n        cluster.go:125: \n        cluster.go:125: To start using your cluster, you need to run the following as a regular user:\n        cluster.go:125: \n        cluster.go:125:   mkdir -p $HOME/.kube\n        cluster.go:125:   sudo cp -i /etc/kubernetes/admin.conf $HOME/.kube/config\n        cluster.go:125:   sudo chown $(id -u):$(id -g) $HOME/.kube/config\n        cluster.go:125: \n        cluster.go:125: Alternatively, if you are the root user, you can run:\n        cluster.go:125: \n        cluster.go:125:   export KUBECONFIG=/etc/kubernetes/admin.conf\n        cluster.go:125: \n        cluster.go:125: You should now deploy a pod network to the cluster.\n        cluster.go:125: Run \"kubectl apply -f [podnetwork].yaml\" with one of the options listed at:\n        cluster.go:125:   https://kubernetes.io/docs/concepts/cluster-administration/addons/\n        cluster.go:125: \n        cluster.go:125: Then you can join any number of worker nodes by running the following on each as root:\n        cluster.go:125: \n        cluster.go:125: kubeadm join 10.0.0.5:6443 --token 66zqob.vyiw1jnzvsvlqxl2 \\\n        cluster.go:125: \t--discovery-token-ca-cert-hash sha256:728bcd57b94b9f5f1857743a0fab0c3e040f437902776319d088cf4b767aa993 \n        cluster.go:125: namespace/kube-flannel created\n        cluster.go:125: clusterrole.rbac.authorization.k8s.io/flannel created\n        cluster.go:125: clusterrolebinding.rbac.authorization.k8s.io/flannel created\n        cluster.go:125: serviceaccount/flannel created\n        cluster.go:125: configmap/kube-flannel-cfg created\n        cluster.go:125: daemonset.apps/kube-flannel-ds created\n        cluster.go:125: W0420 20:41:22.392528    1813 joinconfiguration.go:112] [config] WARNING: Ignored configuration document with GroupVersionKind kubelet.config.k8s.io/v1beta1, Kind=KubeletConfiguration\n        cluster.go:125: \t[WARNING Service-kubelet]: kubelet service is not enabled, please run 'systemctl enable kubelet.service'\n    --- PASS: kubeadm.v1.35.1.flannel.base/node_readiness (21.85s)\n    --- PASS: kubeadm.v1.35.1.flannel.base/nginx_deployment (38.78s)\n    --- PASS: kubeadm.v1.35.1.flannel.base/NFS_deployment (47.11s)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n"},{"name":"kubeadm.v1.34.4.flannel.base/node_readiness","result":"PASS","duration":16944729277,"output":""},{"name":"kubeadm.v1.34.4.flannel.base/nginx_deployment","result":"PASS","duration":18585450820,"output":""},{"name":"kubeadm.v1.34.4.flannel.base/NFS_deployment","result":"PASS","duration":46755116906,"output":"        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n"},{"name":"kubeadm.v1.34.4.flannel.base","result":"PASS","duration":372352106826,"output":"        cluster.go:125: I0420 20:41:07.957791    2037 version.go:260] remote version is much newer: v1.35.4; falling back to: stable-1.34\n        cluster.go:125: [config/images] Pulled registry.k8s.io/kube-apiserver:v1.34.7\n        cluster.go:125: [config/images] Pulled registry.k8s.io/kube-controller-manager:v1.34.7\n        cluster.go:125: [config/images] Pulled registry.k8s.io/kube-scheduler:v1.34.7\n        cluster.go:125: [config/images] Pulled registry.k8s.io/kube-proxy:v1.34.7\n        cluster.go:125: [config/images] Pulled registry.k8s.io/coredns/coredns:v1.12.1\n        cluster.go:125: [config/images] Pulled registry.k8s.io/pause:3.10.1\n        cluster.go:125: [config/images] Pulled registry.k8s.io/etcd:3.6.5-0\n        cluster.go:125: I0420 20:41:51.411726    2327 version.go:260] remote version is much newer: v1.35.4; falling back to: stable-1.34\n        cluster.go:125: [init] Using Kubernetes version: v1.34.7\n        cluster.go:125: [preflight] Running pre-flight checks\n        cluster.go:125: \t[WARNING Service-Kubelet]: kubelet service is not enabled, please run 'systemctl enable kubelet.service'\n        cluster.go:125: [preflight] Pulling images required for setting up a Kubernetes cluster\n        cluster.go:125: [preflight] This might take a minute or two, depending on the speed of your internet connection\n        cluster.go:125: [preflight] You can also perform this action beforehand using 'kubeadm config images pull'\n        cluster.go:125: [certs] Using certificateDir folder \"/etc/kubernetes/pki\"\n        cluster.go:125: [certs] Generating \"ca\" certificate and key\n        cluster.go:125: [certs] Generating \"apiserver\" certificate and key\n        cluster.go:125: [certs] apiserver serving cert is signed for DNS names [kubernetes kubernetes.default kubernetes.default.svc kubernetes.default.svc.cluster.local localhost] and IPs [10.96.0.1 10.0.0.7]\n        cluster.go:125: [certs] Generating \"apiserver-kubelet-client\" certificate and key\n        cluster.go:125: [certs] Generating \"front-proxy-ca\" certificate and key\n        cluster.go:125: [certs] Generating \"front-proxy-client\" certificate and key\n        cluster.go:125: [certs] External etcd mode: Skipping etcd/ca certificate authority generation\n        cluster.go:125: [certs] External etcd mode: Skipping etcd/server certificate generation\n        cluster.go:125: [certs] External etcd mode: Skipping etcd/peer certificate generation\n        cluster.go:125: [certs] External etcd mode: Skipping etcd/healthcheck-client certificate generation\n        cluster.go:125: [certs] External etcd mode: Skipping apiserver-etcd-client certificate generation\n        cluster.go:125: [certs] Generating \"sa\" key and public key\n        cluster.go:125: [kubeconfig] Using kubeconfig folder \"/etc/kubernetes\"\n        cluster.go:125: [kubeconfig] Writing \"admin.conf\" kubeconfig file\n        cluster.go:125: [kubeconfig] Writing \"super-admin.conf\" kubeconfig file\n        cluster.go:125: [kubeconfig] Writing \"kubelet.conf\" kubeconfig file\n        cluster.go:125: [kubeconfig] Writing \"controller-manager.conf\" kubeconfig file\n        cluster.go:125: [kubeconfig] Writing \"scheduler.conf\" kubeconfig file\n        cluster.go:125: [control-plane] Using manifest folder \"/etc/kubernetes/manifests\"\n        cluster.go:125: [control-plane] Creating static Pod manifest for \"kube-apiserver\"\n        cluster.go:125: [control-plane] Creating static Pod manifest for \"kube-controller-manager\"\n        cluster.go:125: [control-plane] Creating static Pod manifest for \"kube-scheduler\"\n        cluster.go:125: [kubelet-start] Writing kubelet environment file with flags to file \"/var/lib/kubelet/kubeadm-flags.env\"\n        cluster.go:125: [kubelet-start] Writing kubelet configuration to file \"/var/lib/kubelet/instance-config.yaml\"\n        cluster.go:125: [patches] Applied patch of type \"application/strategic-merge-patch+json\" to target \"kubeletconfiguration\"\n        cluster.go:125: [kubelet-start] Writing kubelet configuration to file \"/var/lib/kubelet/config.yaml\"\n        cluster.go:125: [kubelet-start] Starting the kubelet\n        cluster.go:125: [wait-control-plane] Waiting for the kubelet to boot up the control plane as static Pods from directory \"/etc/kubernetes/manifests\"\n        cluster.go:125: [kubelet-check] Waiting for a healthy kubelet at http://127.0.0.1:10248/healthz. This can take up to 4m0s\n        cluster.go:125: [kubelet-check] The kubelet is healthy after 2.008476349s\n        cluster.go:125: [control-plane-check] Waiting for healthy control plane components. This can take up to 30m0s\n        cluster.go:125: [control-plane-check] Checking kube-apiserver at https://10.0.0.7:6443/livez\n        cluster.go:125: [control-plane-check] Checking kube-controller-manager at https://127.0.0.1:10257/healthz\n        cluster.go:125: [control-plane-check] Checking kube-scheduler at https://127.0.0.1:10259/livez\n        cluster.go:125: [control-plane-check] kube-controller-manager is healthy after 12.999224793s\n        cluster.go:125: [control-plane-check] kube-scheduler is healthy after 31.874160623s\n        cluster.go:125: [control-plane-check] kube-apiserver is healthy after 1m11.010919024s\n        cluster.go:125: [upload-config] Storing the configuration used in ConfigMap \"kubeadm-config\" in the \"kube-system\" Namespace\n        cluster.go:125: [kubelet] Creating a ConfigMap \"kubelet-config\" in namespace kube-system with the configuration for the kubelets in the cluster\n        cluster.go:125: [upload-certs] Skipping phase. Please see --upload-certs\n        cluster.go:125: [mark-control-plane] Marking the node localhost as control-plane by adding the labels: [node-role.kubernetes.io/control-plane node.kubernetes.io/exclude-from-external-load-balancers]\n        cluster.go:125: [mark-control-plane] Marking the node localhost as control-plane by adding the taints [node-role.kubernetes.io/control-plane:NoSchedule]\n        cluster.go:125: [bootstrap-token] Using token: ioz5z3.2lckf5xo282t2on3\n        cluster.go:125: [bootstrap-token] Configuring bootstrap tokens, cluster-info ConfigMap, RBAC Roles\n        cluster.go:125: [bootstrap-token] Configured RBAC rules to allow Node Bootstrap tokens to get nodes\n        cluster.go:125: [bootstrap-token] Configured RBAC rules to allow Node Bootstrap tokens to post CSRs in order for nodes to get long term certificate credentials\n        cluster.go:125: [bootstrap-token] Configured RBAC rules to allow the csrapprover controller automatically approve CSRs from a Node Bootstrap Token\n        cluster.go:125: [bootstrap-token] Configured RBAC rules to allow certificate rotation for all node client certificates in the cluster\n        cluster.go:125: [bootstrap-token] Creating the \"cluster-info\" ConfigMap in the \"kube-public\" namespace\n        cluster.go:125: [kubelet-finalize] Updating \"/etc/kubernetes/kubelet.conf\" to point to a rotatable kubelet client certificate and key\n        cluster.go:125: [addons] Applied essential addon: CoreDNS\n        cluster.go:125: [addons] Applied essential addon: kube-proxy\n        cluster.go:125: \n        cluster.go:125: Your Kubernetes control-plane has initialized successfully!\n        cluster.go:125: \n        cluster.go:125: To start using your cluster, you need to run the following as a regular user:\n        cluster.go:125: \n        cluster.go:125:   mkdir -p $HOME/.kube\n        cluster.go:125:   sudo cp -i /etc/kubernetes/admin.conf $HOME/.kube/config\n        cluster.go:125:   sudo chown $(id -u):$(id -g) $HOME/.kube/config\n        cluster.go:125: \n        cluster.go:125: Alternatively, if you are the root user, you can run:\n        cluster.go:125: \n        cluster.go:125:   export KUBECONFIG=/etc/kubernetes/admin.conf\n        cluster.go:125: \n        cluster.go:125: You should now deploy a pod network to the cluster.\n        cluster.go:125: Run \"kubectl apply -f [podnetwork].yaml\" with one of the options listed at:\n        cluster.go:125:   https://kubernetes.io/docs/concepts/cluster-administration/addons/\n        cluster.go:125: \n        cluster.go:125: Then you can join any number of worker nodes by running the following on each as root:\n        cluster.go:125: \n        cluster.go:125: kubeadm join 10.0.0.7:6443 --token ioz5z3.2lckf5xo282t2on3 \\\n        cluster.go:125: \t--discovery-token-ca-cert-hash sha256:de05535c53616a4ac4ebe4ccb0f82bf7c155a715b0e47fd33526a65eb301754d \n        cluster.go:125: namespace/kube-flannel created\n        cluster.go:125: clusterrole.rbac.authorization.k8s.io/flannel created\n        cluster.go:125: clusterrolebinding.rbac.authorization.k8s.io/flannel created\n        cluster.go:125: serviceaccount/flannel created\n        cluster.go:125: configmap/kube-flannel-cfg created\n        cluster.go:125: daemonset.apps/kube-flannel-ds created\n        cluster.go:125: W0420 20:44:00.578681    1801 joinconfiguration.go:112] [config] WARNING: Ignored configuration document with GroupVersionKind kubelet.config.k8s.io/v1beta1, Kind=KubeletConfiguration\n        cluster.go:125: \t[WARNING Service-Kubelet]: kubelet service is not enabled, please run 'systemctl enable kubelet.service'\n    --- PASS: kubeadm.v1.34.4.flannel.base/node_readiness (16.94s)\n    --- PASS: kubeadm.v1.34.4.flannel.base/nginx_deployment (18.59s)\n    --- PASS: kubeadm.v1.34.4.flannel.base/NFS_deployment (46.76s)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n"},{"name":"kubeadm.v1.35.1.calico.base/node_readiness","result":"FAIL","duration":208553520871,"output":"        kubeadm.go:213: nodes are not ready: ready nodes should be equal to 2: 1\n"},{"name":"kubeadm.v1.35.1.calico.base/nginx_deployment","result":"PASS","duration":125515001357,"output":""},{"name":"kubeadm.v1.35.1.calico.base/NFS_deployment","result":"FAIL","duration":223395545152,"output":"        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        kubeadm.go:264: nginx pod with NFS is not deployed: getting container status: Process exited with status 5\n"},{"name":"kubeadm.v1.35.1.calico.base","result":"FAIL","duration":936177310706,"output":"        cluster.go:125: [config/images] Pulled registry.k8s.io/kube-apiserver:v1.35.4\n        cluster.go:125: [config/images] Pulled registry.k8s.io/kube-controller-manager:v1.35.4\n        cluster.go:125: [config/images] Pulled registry.k8s.io/kube-scheduler:v1.35.4\n        cluster.go:125: [config/images] Pulled registry.k8s.io/kube-proxy:v1.35.4\n        cluster.go:125: [config/images] Pulled registry.k8s.io/coredns/coredns:v1.13.1\n        cluster.go:125: [config/images] Pulled registry.k8s.io/pause:3.10.1\n        cluster.go:125: [config/images] Pulled registry.k8s.io/etcd:3.6.6-0\n        cluster.go:125: [init] Using Kubernetes version: v1.35.4\n        cluster.go:125: [preflight] Running pre-flight checks\n        cluster.go:125: \t[WARNING Service-kubelet]: kubelet service is not enabled, please run 'systemctl enable kubelet.service'\n        cluster.go:125: [preflight] Pulling images required for setting up a Kubernetes cluster\n        cluster.go:125: [preflight] This might take a minute or two, depending on the speed of your internet connection\n        cluster.go:125: [preflight] You can also perform this action beforehand using 'kubeadm config images pull'\n        cluster.go:125: [certs] Using certificateDir folder \"/etc/kubernetes/pki\"\n        cluster.go:125: [certs] Generating \"ca\" certificate and key\n        cluster.go:125: [certs] Generating \"apiserver\" certificate and key\n        cluster.go:125: [certs] apiserver serving cert is signed for DNS names [kubernetes kubernetes.default kubernetes.default.svc kubernetes.default.svc.cluster.local localhost] and IPs [10.96.0.1 10.0.0.6]\n        cluster.go:125: [certs] Generating \"apiserver-kubelet-client\" certificate and key\n        cluster.go:125: [certs] Generating \"front-proxy-ca\" certificate and key\n        cluster.go:125: [certs] Generating \"front-proxy-client\" certificate and key\n        cluster.go:125: [certs] External etcd mode: Skipping etcd/ca certificate authority generation\n        cluster.go:125: [certs] External etcd mode: Skipping etcd/server certificate generation\n        cluster.go:125: [certs] External etcd mode: Skipping etcd/peer certificate generation\n        cluster.go:125: [certs] External etcd mode: Skipping etcd/healthcheck-client certificate generation\n        cluster.go:125: [certs] External etcd mode: Skipping apiserver-etcd-client certificate generation\n        cluster.go:125: [certs] Generating \"sa\" key and public key\n        cluster.go:125: [kubeconfig] Using kubeconfig folder \"/etc/kubernetes\"\n        cluster.go:125: [kubeconfig] Writing \"admin.conf\" kubeconfig file\n        cluster.go:125: [kubeconfig] Writing \"super-admin.conf\" kubeconfig file\n        cluster.go:125: [kubeconfig] Writing \"kubelet.conf\" kubeconfig file\n        cluster.go:125: [kubeconfig] Writing \"controller-manager.conf\" kubeconfig file\n        cluster.go:125: [kubeconfig] Writing \"scheduler.conf\" kubeconfig file\n        cluster.go:125: [control-plane] Using manifest folder \"/etc/kubernetes/manifests\"\n        cluster.go:125: [control-plane] Creating static Pod manifest for \"kube-apiserver\"\n        cluster.go:125: [control-plane] Creating static Pod manifest for \"kube-controller-manager\"\n        cluster.go:125: [control-plane] Creating static Pod manifest for \"kube-scheduler\"\n        cluster.go:125: [kubelet-start] Writing kubelet environment file with flags to file \"/var/lib/kubelet/kubeadm-flags.env\"\n        cluster.go:125: [kubelet-start] Writing kubelet configuration to file \"/var/lib/kubelet/instance-config.yaml\"\n        cluster.go:125: [patches] Applied patch of type \"application/strategic-merge-patch+json\" to target \"kubeletconfiguration\"\n        cluster.go:125: [kubelet-start] Writing kubelet configuration to file \"/var/lib/kubelet/config.yaml\"\n        cluster.go:125: [kubelet-start] Starting the kubelet\n        cluster.go:125: [wait-control-plane] Waiting for the kubelet to boot up the control plane as static Pods from directory \"/etc/kubernetes/manifests\"\n        cluster.go:125: [kubelet-check] Waiting for a healthy kubelet at http://127.0.0.1:10248/healthz. This can take up to 4m0s\n        cluster.go:125: [kubelet-check] The kubelet is healthy after 1.002341096s\n        cluster.go:125: [control-plane-check] Waiting for healthy control plane components. This can take up to 30m0s\n        cluster.go:125: [control-plane-check] Checking kube-apiserver at https://10.0.0.6:6443/livez\n        cluster.go:125: [control-plane-check] Checking kube-controller-manager at https://127.0.0.1:10257/healthz\n        cluster.go:125: [control-plane-check] Checking kube-scheduler at https://127.0.0.1:10259/livez\n        cluster.go:125: [control-plane-check] kube-controller-manager is healthy after 1.544997043s\n        cluster.go:125: [control-plane-check] kube-scheduler is healthy after 3.215476625s\n        cluster.go:125: [control-plane-check] kube-apiserver is healthy after 6.528103976s\n        cluster.go:125: [upload-config] Storing the configuration used in ConfigMap \"kubeadm-config\" in the \"kube-system\" Namespace\n        cluster.go:125: [kubelet] Creating a ConfigMap \"kubelet-config\" in namespace kube-system with the configuration for the kubelets in the cluster\n        cluster.go:125: [upload-certs] Skipping phase. Please see --upload-certs\n        cluster.go:125: [mark-control-plane] Marking the node localhost as control-plane by adding the labels: [node-role.kubernetes.io/control-plane node.kubernetes.io/exclude-from-external-load-balancers]\n        cluster.go:125: [mark-control-plane] Marking the node localhost as control-plane by adding the taints [node-role.kubernetes.io/control-plane:NoSchedule]\n        cluster.go:125: [bootstrap-token] Using token: gec4jy.dcq0fq0zixokksq5\n        cluster.go:125: [bootstrap-token] Configuring bootstrap tokens, cluster-info ConfigMap, RBAC Roles\n        cluster.go:125: [bootstrap-token] Configured RBAC rules to allow Node Bootstrap tokens to get nodes\n        cluster.go:125: [bootstrap-token] Configured RBAC rules to allow Node Bootstrap tokens to post CSRs in order for nodes to get long term certificate credentials\n        cluster.go:125: [bootstrap-token] Configured RBAC rules to allow the csrapprover controller automatically approve CSRs from a Node Bootstrap Token\n        cluster.go:125: [bootstrap-token] Configured RBAC rules to allow certificate rotation for all node client certificates in the cluster\n        cluster.go:125: [bootstrap-token] Creating the \"cluster-info\" ConfigMap in the \"kube-public\" namespace\n        cluster.go:125: [kubelet-finalize] Updating \"/etc/kubernetes/kubelet.conf\" to point to a rotatable kubelet client certificate and key\n        cluster.go:125: [addons] Applied essential addon: CoreDNS\n        cluster.go:125: [addons] Applied essential addon: kube-proxy\n        cluster.go:125: \n        cluster.go:125: Your Kubernetes control-plane has initialized successfully!\n        cluster.go:125: \n        cluster.go:125: To start using your cluster, you need to run the following as a regular user:\n        cluster.go:125: \n        cluster.go:125:   mkdir -p $HOME/.kube\n        cluster.go:125:   sudo cp -i /etc/kubernetes/admin.conf $HOME/.kube/config\n        cluster.go:125:   sudo chown $(id -u):$(id -g) $HOME/.kube/config\n        cluster.go:125: \n        cluster.go:125: Alternatively, if you are the root user, you can run:\n        cluster.go:125: \n        cluster.go:125:   export KUBECONFIG=/etc/kubernetes/admin.conf\n        cluster.go:125: \n        cluster.go:125: You should now deploy a pod network to the cluster.\n        cluster.go:125: Run \"kubectl apply -f [podnetwork].yaml\" with one of the options listed at:\n        cluster.go:125:   https://kubernetes.io/docs/concepts/cluster-administration/addons/\n        cluster.go:125: \n        cluster.go:125: Then you can join any number of worker nodes by running the following on each as root:\n        cluster.go:125: \n        cluster.go:125: kubeadm join 10.0.0.6:6443 --token gec4jy.dcq0fq0zixokksq5 \\\n        cluster.go:125: \t--discovery-token-ca-cert-hash sha256:0c056a89bcb0f68df6419de9b0237bd0431609b4d78cecfa1cb67ba804cf7dc0 \n        cluster.go:125: namespace/tigera-operator created\n        cluster.go:125: serviceaccount/tigera-operator created\n        cluster.go:125: clusterrole.rbac.authorization.k8s.io/tigera-operator-secrets created\n        cluster.go:125: clusterrole.rbac.authorization.k8s.io/tigera-operator created\n        cluster.go:125: clusterrolebinding.rbac.authorization.k8s.io/tigera-operator created\n        cluster.go:125: rolebinding.rbac.authorization.k8s.io/tigera-operator-secrets created\n        cluster.go:125: deployment.apps/tigera-operator created\n        cluster.go:125: customresourcedefinition.apiextensions.k8s.io/installations.operator.tigera.io condition met\n        cluster.go:125: customresourcedefinition.apiextensions.k8s.io/installations.operator.tigera.io condition met\n        cluster.go:125: customresourcedefinition.apiextensions.k8s.io/apiservers.operator.tigera.io condition met\n        cluster.go:125: customresourcedefinition.apiextensions.k8s.io/apiservers.operator.tigera.io condition met\n        cluster.go:125: installation.operator.tigera.io/default created\n        cluster.go:125: apiserver.operator.tigera.io/default created\n        cluster.go:125: goldmane.operator.tigera.io/default created\n        cluster.go:125: whisker.operator.tigera.io/default created\n        cluster.go:125: W0420 20:44:54.031970    1891 joinconfiguration.go:112] [config] WARNING: Ignored configuration document with GroupVersionKind kubelet.config.k8s.io/v1beta1, Kind=KubeletConfiguration\n        cluster.go:125: \t[WARNING Service-kubelet]: kubelet service is not enabled, please run 'systemctl enable kubelet.service'\n    --- FAIL: kubeadm.v1.35.1.calico.base/node_readiness (208.55s)\n            kubeadm.go:213: nodes are not ready: ready nodes should be equal to 2: 1\n    --- PASS: kubeadm.v1.35.1.calico.base/nginx_deployment (125.52s)\n    --- FAIL: kubeadm.v1.35.1.calico.base/NFS_deployment (223.40s)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            kubeadm.go:264: nginx pod with NFS is not deployed: getting container status: Process exited with status 5\n"},{"name":"kubeadm.v1.33.8.calico.base","result":"FAIL","duration":661663883284,"output":"        kubeadm.go:197: unable to setup cluster: unable to create master node with large disk: machine \"1feb691a-f858-4d1d-a80e-67007a6e2f51\" failed to start: ssh journalctl failed: time limit exceeded: dial tcp 10.0.0.14:22: connect: connection refused\n"},{"name":"kubeadm.v1.34.4.calico.base/node_readiness","result":"PASS","duration":37412396092,"output":""},{"name":"kubeadm.v1.34.4.calico.base/nginx_deployment","result":"PASS","duration":19562787237,"output":""},{"name":"kubeadm.v1.34.4.calico.base/NFS_deployment","result":"PASS","duration":53999720745,"output":"        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n"},{"name":"kubeadm.v1.34.4.calico.base","result":"PASS","duration":369782328094,"output":"        cluster.go:125: I0420 20:57:05.631980    2084 version.go:260] remote version is much newer: v1.35.4; falling back to: stable-1.34\n        cluster.go:125: [config/images] Pulled registry.k8s.io/kube-apiserver:v1.34.7\n        cluster.go:125: [config/images] Pulled registry.k8s.io/kube-controller-manager:v1.34.7\n        cluster.go:125: [config/images] Pulled registry.k8s.io/kube-scheduler:v1.34.7\n        cluster.go:125: [config/images] Pulled registry.k8s.io/kube-proxy:v1.34.7\n        cluster.go:125: [config/images] Pulled registry.k8s.io/coredns/coredns:v1.12.1\n        cluster.go:125: [config/images] Pulled registry.k8s.io/pause:3.10.1\n        cluster.go:125: [config/images] Pulled registry.k8s.io/etcd:3.6.5-0\n        cluster.go:125: I0420 20:57:19.998073    2315 version.go:260] remote version is much newer: v1.35.4; falling back to: stable-1.34\n        cluster.go:125: [init] Using Kubernetes version: v1.34.7\n        cluster.go:125: [preflight] Running pre-flight checks\n        cluster.go:125: \t[WARNING Service-Kubelet]: kubelet service is not enabled, please run 'systemctl enable kubelet.service'\n        cluster.go:125: [preflight] Pulling images required for setting up a Kubernetes cluster\n        cluster.go:125: [preflight] This might take a minute or two, depending on the speed of your internet connection\n        cluster.go:125: [preflight] You can also perform this action beforehand using 'kubeadm config images pull'\n        cluster.go:125: [certs] Using certificateDir folder \"/etc/kubernetes/pki\"\n        cluster.go:125: [certs] Generating \"ca\" certificate and key\n        cluster.go:125: [certs] Generating \"apiserver\" certificate and key\n        cluster.go:125: [certs] apiserver serving cert is signed for DNS names [kubernetes kubernetes.default kubernetes.default.svc kubernetes.default.svc.cluster.local localhost] and IPs [10.96.0.1 10.0.0.17]\n        cluster.go:125: [certs] Generating \"apiserver-kubelet-client\" certificate and key\n        cluster.go:125: [certs] Generating \"front-proxy-ca\" certificate and key\n        cluster.go:125: [certs] Generating \"front-proxy-client\" certificate and key\n        cluster.go:125: [certs] External etcd mode: Skipping etcd/ca certificate authority generation\n        cluster.go:125: [certs] External etcd mode: Skipping etcd/server certificate generation\n        cluster.go:125: [certs] External etcd mode: Skipping etcd/peer certificate generation\n        cluster.go:125: [certs] External etcd mode: Skipping etcd/healthcheck-client certificate generation\n        cluster.go:125: [certs] External etcd mode: Skipping apiserver-etcd-client certificate generation\n        cluster.go:125: [certs] Generating \"sa\" key and public key\n        cluster.go:125: [kubeconfig] Using kubeconfig folder \"/etc/kubernetes\"\n        cluster.go:125: [kubeconfig] Writing \"admin.conf\" kubeconfig file\n        cluster.go:125: [kubeconfig] Writing \"super-admin.conf\" kubeconfig file\n        cluster.go:125: [kubeconfig] Writing \"kubelet.conf\" kubeconfig file\n        cluster.go:125: [kubeconfig] Writing \"controller-manager.conf\" kubeconfig file\n        cluster.go:125: [kubeconfig] Writing \"scheduler.conf\" kubeconfig file\n        cluster.go:125: [control-plane] Using manifest folder \"/etc/kubernetes/manifests\"\n        cluster.go:125: [control-plane] Creating static Pod manifest for \"kube-apiserver\"\n        cluster.go:125: [control-plane] Creating static Pod manifest for \"kube-controller-manager\"\n        cluster.go:125: [control-plane] Creating static Pod manifest for \"kube-scheduler\"\n        cluster.go:125: [kubelet-start] Writing kubelet environment file with flags to file \"/var/lib/kubelet/kubeadm-flags.env\"\n        cluster.go:125: [kubelet-start] Writing kubelet configuration to file \"/var/lib/kubelet/instance-config.yaml\"\n        cluster.go:125: [patches] Applied patch of type \"application/strategic-merge-patch+json\" to target \"kubeletconfiguration\"\n        cluster.go:125: [kubelet-start] Writing kubelet configuration to file \"/var/lib/kubelet/config.yaml\"\n        cluster.go:125: [kubelet-start] Starting the kubelet\n        cluster.go:125: [wait-control-plane] Waiting for the kubelet to boot up the control plane as static Pods from directory \"/etc/kubernetes/manifests\"\n        cluster.go:125: [kubelet-check] Waiting for a healthy kubelet at http://127.0.0.1:10248/healthz. This can take up to 4m0s\n        cluster.go:125: [kubelet-check] The kubelet is healthy after 1.543579359s\n        cluster.go:125: [control-plane-check] Waiting for healthy control plane components. This can take up to 30m0s\n        cluster.go:125: [control-plane-check] Checking kube-apiserver at https://10.0.0.17:6443/livez\n        cluster.go:125: [control-plane-check] Checking kube-controller-manager at https://127.0.0.1:10257/healthz\n        cluster.go:125: [control-plane-check] Checking kube-scheduler at https://127.0.0.1:10259/livez\n        cluster.go:125: [control-plane-check] kube-controller-manager is healthy after 2.008219332s\n        cluster.go:125: [control-plane-check] kube-scheduler is healthy after 3.00938077s\n        cluster.go:125: [control-plane-check] kube-apiserver is healthy after 7.506097298s\n        cluster.go:125: [upload-config] Storing the configuration used in ConfigMap \"kubeadm-config\" in the \"kube-system\" Namespace\n        cluster.go:125: [kubelet] Creating a ConfigMap \"kubelet-config\" in namespace kube-system with the configuration for the kubelets in the cluster\n        cluster.go:125: [upload-certs] Skipping phase. Please see --upload-certs\n        cluster.go:125: [mark-control-plane] Marking the node localhost as control-plane by adding the labels: [node-role.kubernetes.io/control-plane node.kubernetes.io/exclude-from-external-load-balancers]\n        cluster.go:125: [mark-control-plane] Marking the node localhost as control-plane by adding the taints [node-role.kubernetes.io/control-plane:NoSchedule]\n        cluster.go:125: [bootstrap-token] Using token: be5mqa.q5fjvu4z7d4bmd8p\n        cluster.go:125: [bootstrap-token] Configuring bootstrap tokens, cluster-info ConfigMap, RBAC Roles\n        cluster.go:125: [bootstrap-token] Configured RBAC rules to allow Node Bootstrap tokens to get nodes\n        cluster.go:125: [bootstrap-token] Configured RBAC rules to allow Node Bootstrap tokens to post CSRs in order for nodes to get long term certificate credentials\n        cluster.go:125: [bootstrap-token] Configured RBAC rules to allow the csrapprover controller automatically approve CSRs from a Node Bootstrap Token\n        cluster.go:125: [bootstrap-token] Configured RBAC rules to allow certificate rotation for all node client certificates in the cluster\n        cluster.go:125: [bootstrap-token] Creating the \"cluster-info\" ConfigMap in the \"kube-public\" namespace\n        cluster.go:125: [kubelet-finalize] Updating \"/etc/kubernetes/kubelet.conf\" to point to a rotatable kubelet client certificate and key\n        cluster.go:125: [addons] Applied essential addon: CoreDNS\n        cluster.go:125: [addons] Applied essential addon: kube-proxy\n        cluster.go:125: \n        cluster.go:125: Your Kubernetes control-plane has initialized successfully!\n        cluster.go:125: \n        cluster.go:125: To start using your cluster, you need to run the following as a regular user:\n        cluster.go:125: \n        cluster.go:125:   mkdir -p $HOME/.kube\n        cluster.go:125:   sudo cp -i /etc/kubernetes/admin.conf $HOME/.kube/config\n        cluster.go:125:   sudo chown $(id -u):$(id -g) $HOME/.kube/config\n        cluster.go:125: \n        cluster.go:125: Alternatively, if you are the root user, you can run:\n        cluster.go:125: \n        cluster.go:125:   export KUBECONFIG=/etc/kubernetes/admin.conf\n        cluster.go:125: \n        cluster.go:125: You should now deploy a pod network to the cluster.\n        cluster.go:125: Run \"kubectl apply -f [podnetwork].yaml\" with one of the options listed at:\n        cluster.go:125:   https://kubernetes.io/docs/concepts/cluster-administration/addons/\n        cluster.go:125: \n        cluster.go:125: Then you can join any number of worker nodes by running the following on each as root:\n        cluster.go:125: \n        cluster.go:125: kubeadm join 10.0.0.17:6443 --token be5mqa.q5fjvu4z7d4bmd8p \\\n        cluster.go:125: \t--discovery-token-ca-cert-hash sha256:bc21ab371d5ced48850fdc971878e159b05ffdf5242fd56f7702fbe6ff104934 \n        cluster.go:125: namespace/tigera-operator created\n        cluster.go:125: serviceaccount/tigera-operator created\n        cluster.go:125: clusterrole.rbac.authorization.k8s.io/tigera-operator-secrets created\n        cluster.go:125: clusterrole.rbac.authorization.k8s.io/tigera-operator created\n        cluster.go:125: clusterrolebinding.rbac.authorization.k8s.io/tigera-operator created\n        cluster.go:125: rolebinding.rbac.authorization.k8s.io/tigera-operator-secrets created\n        cluster.go:125: deployment.apps/tigera-operator created\n        cluster.go:125: customresourcedefinition.apiextensions.k8s.io/installations.operator.tigera.io condition met\n        cluster.go:125: customresourcedefinition.apiextensions.k8s.io/installations.operator.tigera.io condition met\n        cluster.go:125: customresourcedefinition.apiextensions.k8s.io/apiservers.operator.tigera.io condition met\n        cluster.go:125: customresourcedefinition.apiextensions.k8s.io/apiservers.operator.tigera.io condition met\n        cluster.go:125: installation.operator.tigera.io/default created\n        cluster.go:125: apiserver.operator.tigera.io/default created\n        cluster.go:125: goldmane.operator.tigera.io/default created\n        cluster.go:125: whisker.operator.tigera.io/default created\n        cluster.go:125: W0420 20:59:03.934675    1867 joinconfiguration.go:112] [config] WARNING: Ignored configuration document with GroupVersionKind kubelet.config.k8s.io/v1beta1, Kind=KubeletConfiguration\n        cluster.go:125: \t[WARNING Service-Kubelet]: kubelet service is not enabled, please run 'systemctl enable kubelet.service'\n    --- PASS: kubeadm.v1.34.4.calico.base/node_readiness (37.41s)\n    --- PASS: kubeadm.v1.34.4.calico.base/nginx_deployment (19.56s)\n    --- PASS: kubeadm.v1.34.4.calico.base/NFS_deployment (54.00s)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:123): Cannot iterate over null (null)\n"},{"name":"kubeadm.v1.33.8.cilium.base/node_readiness","result":"PASS","duration":118929566436,"output":""},{"name":"kubeadm.v1.33.8.cilium.base/nginx_deployment","result":"PASS","duration":317297161964,"output":""},{"name":"kubeadm.v1.33.8.cilium.base/NFS_deployment","result":"PASS","duration":137152399942,"output":"        cluster.go:125: jq: error (at \u003cstdin\u003e:112): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:112): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:112): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:122): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:122): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:122): Cannot iterate over null (null)\n        cluster.go:125: jq: error (at \u003cstdin\u003e:122): Cannot iterate over null (null)\n"},{"name":"kubeadm.v1.33.8.cilium.base/IPSec_encryption","result":"FAIL","duration":105635738592,"output":"        cluster.go:125: level=warning msg=\"spec.template.metadata.annotations[container.apparmor.security.beta.kubernetes.io/mount-cgroup]: deprecated since v1.30; use the \\\"appArmorProfile\\\" field instead\" subsys=klog\n        cluster.go:125: level=warning msg=\"spec.template.metadata.annotations[container.apparmor.security.beta.kubernetes.io/apply-sysctl-overwrites]: deprecated since v1.30; use the \\\"appArmorProfile\\\" field instead\" subsys=klog\n        cluster.go:125: level=warning msg=\"spec.template.metadata.annotations[container.apparmor.security.beta.kubernetes.io/clean-cilium-state]: deprecated since v1.30; use the \\\"appArmorProfile\\\" field instead\" subsys=klog\n        cluster.go:125: level=warning msg=\"spec.template.metadata.annotations[container.apparmor.security.beta.kubernetes.io/cilium-agent]: deprecated since v1.30; use the \\\"appArmorProfile\\\" field instead\" subsys=klog\n        cluster.go:125: Error: Unable to determine status:  timeout while waiting for status to become successful: context deadline exceeded\n        cluster.go:145: \"/opt/bin/cilium status --wait --wait-duration 1m\" failed: output \u001b[33m    /¯¯\\\n\u001b[36m /¯¯\u001b[33m\\__/\u001b[32m¯¯\\\u001b[0m    Cilium:         \u001b[31m1 errors\u001b[0m, \u001b[33m1 warnings\u001b[0m\n\u001b[36m \\__\u001b[31m/¯¯\\\u001b[32m__/\u001b[0m    Operator:       \u001b[32mOK\u001b[0m\n\u001b[32m /¯¯\u001b[31m\\__/\u001b[35m¯¯\\\u001b[0m    Hubble:         \u001b[36mdisabled\u001b[0m\n\u001b[32m \\__\u001b[34m/¯¯\\\u001b[35m__/\u001b[0m    ClusterMesh:    \u001b[36mdisabled\u001b[0m\n\u001b[34m    \\__/\n\u001b[0m\nDeployment        cilium-operator    Desired: 1, Ready: \u001b[32m1/1\u001b[0m, Available: \u001b[32m1/1\u001b[0m\nDaemonSet         cilium             Desired: 2, Unavailable: \u001b[31m2/2\u001b[0m\nContainers:       cilium             Pending: \u001b[32m1\u001b[0m, Running: \u001b[32m1\u001b[0m\n                  cilium-operator    Running: \u001b[32m1\u001b[0m\nCluster Pods:     5/5 managed by Cilium\nImage versions    cilium-operator    quay.io/cilium/operator-generic:v1.12.5@sha256:b296eb7f0f7656a5cc19724f40a8a7121b7fd725278b7d61dc91fe0b7ffd7c0e: 1\n                  cilium             quay.io/cilium/cilium:v1.12.5@sha256:06ce2b0a0a472e73334a7504ee5c5d8b2e2d7b72ef728ad94e564740dd505be5: 2\nErrors:           cilium             cilium          2 pods of DaemonSet cilium are not ready\nWarnings:         cilium             cilium-8n5zf    pod is pending, status Process exited with status 1\n"},{"name":"kubeadm.v1.33.8.cilium.base","result":"FAIL","duration":1770697858241,"output":"        cluster.go:125: I0420 20:45:45.373092    2108 version.go:261] remote version is much newer: v1.35.4; falling back to: stable-1.33\n        cluster.go:125: [config/images] Pulled registry.k8s.io/kube-apiserver:v1.33.11\n        cluster.go:125: [config/images] Pulled registry.k8s.io/kube-controller-manager:v1.33.11\n        cluster.go:125: [config/images] Pulled registry.k8s.io/kube-scheduler:v1.33.11\n        cluster.go:125: [config/images] Pulled registry.k8s.io/kube-proxy:v1.33.11\n        cluster.go:125: [config/images] Pulled registry.k8s.io/coredns/coredns:v1.12.0\n        cluster.go:125: [config/images] Pulled registry.k8s.io/pause:3.10\n        cluster.go:125: [config/images] Pulled registry.k8s.io/etcd:3.5.24-0\n        cluster.go:125: I0420 20:47:54.563252    2514 version.go:261] remote version is much newer: v1.35.4; falling back to: stable-1.33\n        cluster.go:125: [init] Using Kubernetes version: v1.33.11\n        cluster.go:125: [preflight] Running pre-flight checks\n        cluster.go:125: \t[WARNING Service-Kubelet]: kubelet service is not enabled, please run 'systemctl enable kubelet.service'\n        cluster.go:125: [preflight] Pulling images required for setting up a Kubernetes cluster\n        cluster.go:125: [preflight] This might take a minute or two, depending on the speed of your internet connection\n        cluster.go:125: [preflight] You can also perform this action beforehand using 'kubeadm config images pull'\n        cluster.go:125: [certs] Using certificateDir folder \"/etc/kubernetes/pki\"\n        cluster.go:125: [certs] Generating \"ca\" certificate and key\n        cluster.go:125: [certs] Generating \"apiserver\" certificate and key\n        cluster.go:125: [certs] apiserver serving cert is signed for DNS names [kubernetes kubernetes.default kubernetes.default.svc kubernetes.default.svc.cluster.local localhost] and IPs [10.96.0.1 10.0.0.12]\n        cluster.go:125: [certs] Generating \"apiserver-kubelet-client\" certificate and key\n        cluster.go:125: [certs] Generating \"front-proxy-ca\" certificate and key\n        cluster.go:125: [certs] Generating \"front-proxy-client\" certificate and key\n        cluster.go:125: [certs] External etcd mode: Skipping etcd/ca certificate authority generation\n        cluster.go:125: [certs] External etcd mode: Skipping etcd/server certificate generation\n        cluster.go:125: [certs] External etcd mode: Skipping etcd/peer certificate generation\n        cluster.go:125: [certs] External etcd mode: Skipping etcd/healthcheck-client certificate generation\n        cluster.go:125: [certs] External etcd mode: Skipping apiserver-etcd-client certificate generation\n        cluster.go:125: [certs] Generating \"sa\" key and public key\n        cluster.go:125: [kubeconfig] Using kubeconfig folder \"/etc/kubernetes\"\n        cluster.go:125: [kubeconfig] Writing \"admin.conf\" kubeconfig file\n        cluster.go:125: [kubeconfig] Writing \"super-admin.conf\" kubeconfig file\n        cluster.go:125: [kubeconfig] Writing \"kubelet.conf\" kubeconfig file\n        cluster.go:125: [kubeconfig] Writing \"controller-manager.conf\" kubeconfig file\n        cluster.go:125: [kubeconfig] Writing \"scheduler.conf\" kubeconfig file\n        cluster.go:125: [control-plane] Using manifest folder \"/etc/kubernetes/manifests\"\n        cluster.go:125: [control-plane] Creating static Pod manifest for \"kube-apiserver\"\n        cluster.go:125: [control-plane] Creating static Pod manifest for \"kube-controller-manager\"\n        cluster.go:125: [control-plane] Creating static Pod manifest for \"kube-scheduler\"\n        cluster.go:125: [kubelet-start] Writing kubelet environment file with flags to file \"/var/lib/kubelet/kubeadm-flags.env\"\n        cluster.go:125: [kubelet-start] Writing kubelet configuration to file \"/var/lib/kubelet/config.yaml\"\n        cluster.go:125: [kubelet-start] Starting the kubelet\n        cluster.go:125: [wait-control-plane] Waiting for the kubelet to boot up the control plane as static Pods from directory \"/etc/kubernetes/manifests\"\n        cluster.go:125: [kubelet-check] Waiting for a healthy kubelet at http://127.0.0.1:10248/healthz. This can take up to 4m0s\n        cluster.go:125: [kubelet-check] The kubelet is healthy after 3.050856068s\n        cluster.go:125: [control-plane-check] Waiting for healthy control plane components. This can take up to 30m0s\n        cluster.go:125: [control-plane-check] Checking kube-apiserver at https://10.0.0.12:6443/livez\n        cluster.go:125: [control-plane-check] Checking kube-controller-manager at https://127.0.0.1:10257/healthz\n        cluster.go:125: [control-plane-check] Checking kube-scheduler at https://127.0.0.1:10259/livez\n        cluster.go:125: [control-plane-check] kube-controller-manager is healthy after 23.277199269s\n        cluster.go:125: [control-plane-check] kube-scheduler is healthy after 45.978136868s\n        cluster.go:125: [control-plane-check] kube-apiserver is healthy after 2m4.610378107s\n        cluster.go:125: [upload-config] Storing the configuration used in ConfigMap \"kubeadm-config\" in the \"kube-system\" Namespace\n        cluster.go:125: [kubelet] Creating a ConfigMap \"kubelet-config\" in namespace kube-system with the configuration for the kubelets in the cluster\n        cluster.go:125: [upload-certs] Skipping phase. Please see --upload-certs\n        cluster.go:125: [mark-control-plane] Marking the node localhost as control-plane by adding the labels: [node-role.kubernetes.io/control-plane node.kubernetes.io/exclude-from-external-load-balancers]\n        cluster.go:125: [mark-control-plane] Marking the node localhost as control-plane by adding the taints [node-role.kubernetes.io/control-plane:NoSchedule]\n        cluster.go:125: [bootstrap-token] Using token: jxsjbi.7b02ovnbz9s116y5\n        cluster.go:125: [bootstrap-token] Configuring bootstrap tokens, cluster-info ConfigMap, RBAC Roles\n        cluster.go:125: [bootstrap-token] Configured RBAC rules to allow Node Bootstrap tokens to get nodes\n        cluster.go:125: [bootstrap-token] Configured RBAC rules to allow Node Bootstrap tokens to post CSRs in order for nodes to get long term certificate credentials\n        cluster.go:125: [bootstrap-token] Configured RBAC rules to allow the csrapprover controller automatically approve CSRs from a Node Bootstrap Token\n        cluster.go:125: [bootstrap-token] Configured RBAC rules to allow certificate rotation for all node client certificates in the cluster\n        cluster.go:125: [bootstrap-token] Creating the \"cluster-info\" ConfigMap in the \"kube-public\" namespace\n        cluster.go:125: [kubelet-finalize] Updating \"/etc/kubernetes/kubelet.conf\" to point to a rotatable kubelet client certificate and key\n        cluster.go:125: [addons] Applied essential addon: CoreDNS\n        cluster.go:125: [addons] Applied essential addon: kube-proxy\n        cluster.go:125: \n        cluster.go:125: Your Kubernetes control-plane has initialized successfully!\n        cluster.go:125: \n        cluster.go:125: To start using your cluster, you need to run the following as a regular user:\n        cluster.go:125: \n        cluster.go:125:   mkdir -p $HOME/.kube\n        cluster.go:125:   sudo cp -i /etc/kubernetes/admin.conf $HOME/.kube/config\n        cluster.go:125:   sudo chown $(id -u):$(id -g) $HOME/.kube/config\n        cluster.go:125: \n        cluster.go:125: Alternatively, if you are the root user, you can run:\n        cluster.go:125: \n        cluster.go:125:   export KUBECONFIG=/etc/kubernetes/admin.conf\n        cluster.go:125: \n        cluster.go:125: You should now deploy a pod network to the cluster.\n        cluster.go:125: Run \"kubectl apply -f [podnetwork].yaml\" with one of the options listed at:\n        cluster.go:125:   https://kubernetes.io/docs/concepts/cluster-administration/addons/\n        cluster.go:125: \n        cluster.go:125: Then you can join any number of worker nodes by running the following on each as root:\n        cluster.go:125: \n        cluster.go:125: kubeadm join 10.0.0.12:6443 --token jxsjbi.7b02ovnbz9s116y5 \\\n        cluster.go:125: \t--discovery-token-ca-cert-hash sha256:a75cd816f66d345a1cdc515883c518bc84c43f58e1ca2536f4d8692432b0b712 \n        cluster.go:125: i  Using Cilium version 1.12.5\n        cluster.go:125: ? Auto-detected cluster name: kubernetes\n        cluster.go:125: ? Auto-detected datapath mode: tunnel\n        cluster.go:125: ? Auto-detected kube-proxy has been installed\n        cluster.go:125: i  helm template --namespace kube-system cilium cilium/cilium --version 1.12.5 --set cluster.id=0,cluster.name=kubernetes,encryption.nodeEncryption=false,extraConfig.cluster-pool-ipv4-cidr=192.168.0.0/17,extraConfig.enable-endpoint-routes=true,kubeProxyReplacement=disabled,operator.replicas=1,serviceAccounts.cilium.name=cilium,serviceAccounts.operator.name=cilium-operator,tunnel=vxlan\n        cluster.go:125: i  Storing helm values file in kube-system/cilium-cli-helm-values Secret\n        cluster.go:125: ? Created CA in secret cilium-ca\n        cluster.go:125: ? Generating certificates for Hubble...\n        cluster.go:125: ? Creating Service accounts...\n        cluster.go:125: ? Creating Cluster roles...\n        cluster.go:125: ? Creating ConfigMap for Cilium version 1.12.5...\n        cluster.go:125: i  Manual overwrite in ConfigMap: enable-endpoint-routes=true\n        cluster.go:125: i  Manual overwrite in ConfigMap: cluster-pool-ipv4-cidr=192.168.0.0/17\n        cluster.go:125: ? Creating Agent DaemonSet...\n        cluster.go:125: level=warning msg=\"spec.template.metadata.annotations[container.apparmor.security.beta.kubernetes.io/mount-cgroup]: deprecated since v1.30; use the \\\"appArmorProfile\\\" field instead\" subsys=klog\n        cluster.go:125: level=warning msg=\"spec.template.metadata.annotations[container.apparmor.security.beta.kubernetes.io/apply-sysctl-overwrites]: deprecated since v1.30; use the \\\"appArmorProfile\\\" field instead\" subsys=klog\n        cluster.go:125: level=warning msg=\"spec.template.metadata.annotations[container.apparmor.security.beta.kubernetes.io/clean-cilium-state]: deprecated since v1.30; use the \\\"appArmorProfile\\\" field instead\" subsys=klog\n        cluster.go:125: level=warning msg=\"spec.template.metadata.annotations[container.apparmor.security.beta.kubernetes.io/cilium-agent]: deprecated since v1.30; use the \\\"appArmorProfile\\\" field instead\" subsys=klog\n        cluster.go:125: ? Creating Operator Deployment...\n        cluster.go:125: ? Waiting for Cilium to be installed and ready...\n        cluster.go:125: ? Cilium was successfully installed! Run 'cilium status' to view installation health\n        cluster.go:125: \u001b[33m    /??\\\n        cluster.go:125: \u001b[36m /??\u001b[33m\\__/\u001b[32m??\\\u001b[0m    Cilium:         \u001b[32mOK\u001b[0m\n        cluster.go:125: \u001b[36m \\__\u001b[31m/??\\\u001b[32m__/\u001b[0m    Operator:       \u001b[32mOK\u001b[0m\n        cluster.go:125: \u001b[32m /??\u001b[31m\\__/\u001b[35m??\\\u001b[0m    Hubble:         \u001b[36mdisabled\u001b[0m\n        cluster.go:125: \u001b[32m \\__\u001b[34m/??\\\u001b[35m__/\u001b[0m    ClusterMesh:    \u001b[36mdisabled\u001b[0m\n        cluster.go:125: \u001b[34m    \\__/\n        cluster.go:125: \u001b[0m\n        cluster.go:125: DaemonSet        cilium             \n        cluster.go:125: Deployment       cilium-operator    \n        cluster.go:125: Containers:      cilium             \n        cluster.go:125:                  cilium-operator    \n        cluster.go:125: Cluster Pods:    0/0 managed by Cilium\n        cluster.go:125: W0420 21:01:06.967114    1939 joinconfiguration.go:113] [config] WARNING: Ignored configuration document with GroupVersionKind kubelet.config.k8s.io/v1beta1, Kind=KubeletConfiguration\n        cluster.go:125: \t[WARNING Service-Kubelet]: kubelet service is not enabled, please run 'systemctl enable kubelet.service'\n    --- PASS: kubeadm.v1.33.8.cilium.base/node_readiness (118.93s)\n    --- PASS: kubeadm.v1.33.8.cilium.base/nginx_deployment (317.30s)\n    --- PASS: kubeadm.v1.33.8.cilium.base/NFS_deployment (137.15s)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:112): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:112): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:112): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:122): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:122): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:122): Cannot iterate over null (null)\n            cluster.go:125: jq: error (at \u003cstdin\u003e:122): Cannot iterate over null (null)\n    --- FAIL: kubeadm.v1.33.8.cilium.base/IPSec_encryption (105.64s)\n            cluster.go:125: level=warning msg=\"spec.template.metadata.annotations[container.apparmor.security.beta.kubernetes.io/mount-cgroup]: deprecated since v1.30; use the \\\"appArmorProfile\\\" field instead\" subsys=klog\n            cluster.go:125: level=warning msg=\"spec.template.metadata.annotations[container.apparmor.security.beta.kubernetes.io/apply-sysctl-overwrites]: deprecated since v1.30; use the \\\"appArmorProfile\\\" field instead\" subsys=klog\n            cluster.go:125: level=warning msg=\"spec.template.metadata.annotations[container.apparmor.security.beta.kubernetes.io/clean-cilium-state]: deprecated since v1.30; use the \\\"appArmorProfile\\\" field instead\" subsys=klog\n            cluster.go:125: level=warning msg=\"spec.template.metadata.annotations[container.apparmor.security.beta.kubernetes.io/cilium-agent]: deprecated since v1.30; use the \\\"appArmorProfile\\\" field instead\" subsys=klog\n            cluster.go:125: Error: Unable to determine status:  timeout while waiting for status to become successful: context deadline exceeded\n            cluster.go:145: \"/opt/bin/cilium status --wait --wait-duration 1m\" failed: output \u001b[33m    /¯¯\\\n    \u001b[36m /¯¯\u001b[33m\\__/\u001b[32m¯¯\\\u001b[0m    Cilium:         \u001b[31m1 errors\u001b[0m, \u001b[33m1 warnings\u001b[0m\n    \u001b[36m \\__\u001b[31m/¯¯\\\u001b[32m__/\u001b[0m    Operator:       \u001b[32mOK\u001b[0m\n    \u001b[32m /¯¯\u001b[31m\\__/\u001b[35m¯¯\\\u001b[0m    Hubble:         \u001b[36mdisabled\u001b[0m\n    \u001b[32m \\__\u001b[34m/¯¯\\\u001b[35m__/\u001b[0m    ClusterMesh:    \u001b[36mdisabled\u001b[0m\n    \u001b[34m    \\__/\n    \u001b[0m\n    Deployment        cilium-operator    Desired: 1, Ready: \u001b[32m1/1\u001b[0m, Available: \u001b[32m1/1\u001b[0m\n    DaemonSet         cilium             Desired: 2, Unavailable: \u001b[31m2/2\u001b[0m\n    Containers:       cilium             Pending: \u001b[32m1\u001b[0m, Running: \u001b[32m1\u001b[0m\n                      cilium-operator    Running: \u001b[32m1\u001b[0m\n    Cluster Pods:     5/5 managed by Cilium\n    Image versions    cilium-operator    quay.io/cilium/operator-generic:v1.12.5@sha256:b296eb7f0f7656a5cc19724f40a8a7121b7fd725278b7d61dc91fe0b7ffd7c0e: 1\n                      cilium             quay.io/cilium/cilium:v1.12.5@sha256:06ce2b0a0a472e73334a7504ee5c5d8b2e2d7b72ef728ad94e564740dd505be5: 2\n    Errors:           cilium             cilium          2 pods of DaemonSet cilium are not ready\n    Warnings:         cilium             cilium-8n5zf    pod is pending, status Process exited with status 1\n"}],"result":"FAIL","platform":"qemu","version":"4669.0.0"}